Tag Archives: replace roof shingles

Roofing Tools to Replace Roof Shingles

The procedure was simple once I was positioned comfortably on the roof. It is illustrated below:-

· Lift the shingle tab of the shingle two rows above the shingle I wished to replace shingle.

· Remove the nails from around the shingle tab

· Use the flat pry bar to lift the shingle and keep it securely at a place from where it will not slide down.

· Use the hammer claw to remove all nails around the shingle such that the shingle or a part of it can be removed with ease.

· Place the new shingle in place of the old one and fix the new nails at a place where there is no hole from previous fixings.

· Apply adhesives to the required place.

Certain precautions to take while replacing a new shingle are as follows:

· Choose a shingle of a similar shade when replacing it.

· When installing a new roof, keep at least 20 shingles for such conditions of replacements.

· Don’t replace the entire shingle when only a part is to be replaced. Cut the bad part and put a new one over it.

· Don’t lean on the edge of a roof while replacing a shingle close to the gutter.

· In case there is a requirement to install a shingle near the edge of a roof, use a ladder or scaffolding.

· Consult an experienced roofer prior to starting work. This will also ensure that you don’t do more damage to the roof.

Shingle replacement is an easy operation and can be attempted by a person after taking the requisite precautions. It is however advisable to take assistance from an experienced roofer. Once you get the hang of it, its simple and easy.

As a Virginia, VA Roofing Contractor, Roofer911.com takes great pride in maintaining customer satisfaction for all types of new roof installation and roof repair work for residential and commercial roofing accounts.

You can learn more about how to replace roof shingles, and any other necessary tools and instruments to help with it.

To learn more about how to replace roof shingles, and any other necessary tools and instruments to help with it, check out this article.

By Steven Briesemeister

Article Source: http://EzineArticles.com/?expert=Steven_Briesemeister

http://EzineArticles.com/?Replace-Roof-Shingle—Roofing-Tools-and-Procedures&id=257769

CONTINUE READING

Replace Roof Shingles Yourself – By Following This Guide

As per the doityourself.com, it is a basic operation to replace a shingle and takes approximately 5 minutes. I tried it and as it turned out, it was not so simple. First, it requires some expertise to align at the right angle on the roof to do a good job.

This is a very important aspect of the repair as the person attempting the repair has to be positioned comfortably and securely. A drop from the roof is not the best of things to happen! Once the person has secured himself or herself to a respectable and comfortable position, it is time to start handling the tools. The tools required for replacing a shingle are as follows:-

· Flat pry bar to lift the shingle

· Hammer

· Nails

· Razor Knife

· Adhesive

That’s it!

You can learn more about how to replace roof shingles, and any other necessary tools and instruments to help with it.

By Steven Briesemeister

Article Source: http://EzineArticles.com/?expert=Steven_Briesemeister

http://EzineArticles.com/?Replace-Roof-Shingle—Roofing-Tools-and-Procedures&id=257769

CONTINUE READING

Replacing Roof Shingles A Must For All Homeowners

There are certain musts like replacing roof shingles when they turn 20 years or older. Until a few years ago most asphalt shingles were 20-year shingles and since they were an economical and viable option most homes sported these shingles. Now a days there are more options with 20-year, 30-year, 40-year and 50-year shingles. Metal shingles come with 50-year warranty.

The norms have changed and today 30-year shingles are the norm. Almost every homeowner has to deal with the task of replacing roof shingles at some point in their life. Unless, you are lucky enough to purchase a home whose roof was recently replaced and you sell it before the roofing shingles deteriorates with age or you have a home with metal roof, you will have to face the unenviable task of replacing your roof.

If you are the unlucky few then you might be faced with the task of replacing roof shingles sooner than you planned. This happens when for different reasons a newly installed roof fails and needs replacement. Replacing roof shingles is an expensive and takes a lot of time, but it is also a task that can’t be put off for long, as this longer report explains.

CONTINUE READING

Replace Roof Shingles With Minimum Delay

To replace roof shingles as soon as possible a homeowner needs to be alert and committed to their responsibilities. If the damaged shingles are not replaced as soon as you notice them then you might end up replacing the entire roof, the cost of which will be several thousand dollars more. Maintenance is the key here.

Homeowners needs to makes annual inspections and also at other times like after a rainstorm, hurricane or blizzard. If you notice anything amiss like shingles missing, any sign of damage like broken shingles, cracked shingles, curled and warped shingles, then as a homeowner you should take immediate steps to mend them. Water can seep through even the slightest cracks in the roof.

Water seepage can ruin your interiors, your decking, the plywood sheets, paint job, insulation and much more. The damage can be expensive and extensive if neglected or ignored for long. It is important to replace roof shingles that are damaged in a timely manner.

CONTINUE READING

How To Replace Roof Shingles?

An oft asked question is how to replace roof shingles? Homeowners are faced with the problems of minor or major roof damage at many points in their life. For example a rainstorm or hurricane could have removed a few roof shingles. The impact of falling debris might have cracked brittle shingles. Or the entire roof might have outlived its life and need replacement due to age. The minor problems are easily sorted by the homeowner with a little bit of knowledge and skills.

With a little bit of knowledge you can do minor repairs yourself instead of employing costly labor. But, before you even attempt to get on the roof you should learn about safety first. Roofing projects are usually several feet above ground. People who have fear of the heights or feel giddy due to medication should not attempt this under any circumstances. It can be dangerous unless all safety precautions are taken.

The ladder should be secure, you should have at least one assistant who can help if needed, keep clear of power lines, use special equipment for working on steep slopes and so on. Learn more about the precautions to take and other helpful tips on how to replace roof shingles in this longer article on the topic here.

CONTINUE READING

Replacing Roof Shingles – When It’s Time To Go For A New Roof

Replacing roof shingles becomes a must if your roof is 20 years or older. 20 year shingles were the norm for a long time and most homes were installed with those shingles. Today you get longer lasting shingles and other roofing options like metal and slate which guarantee 50 years or more for their roof.

Today, the standard in asphalt roofing shingles is 30 years. Most homeowners have to deal with the problem of replacing roof shingles at some point in their lives. Unless you bought a home whose roof was recently replaced or it comes with metal or slate roofing which several decades, it becomes imperative at some point to go for roof replacement.

Sometimes, homeowners are faced with task of replacing roof shingles even though the roof was recently installed. Due to a variety of reasons the roof gets damaged and needs to be replaced. This is a very expensive and time-intensive effort which can’t be put off for long.

Let’s explore the causes for roof damage. In the northern parts of the country it is snowstorms and blizzards, strong icy winds, which rip the roofs away. In the south it’s ice storms and hail. The falling debris can damage the shingles, also this clogs the gutters and rips the shingles off their edges of the roofs. Gutters needs to be kept clean to prevent such problems. This can part of your yearly or half-yearly maintenance of your roof. Remove an soil, leaves, branches and other debris from the roof.

If you find any loose shingles, nail them back. Removed curled, damaged or broken shingles and replace them immediately. Loose vents and shingles act as the catalyst for bigger damage, because they provide sort of leverage for the wind to tug and remove other shingles in the line or surroundings. These leaves part of the roof exposed and letting water, snow or ice a free passage to the deck and the house beneath it. Such small problems need to be fixed immediately because the water damage can ruin your paint job, electrical work, cause the wood to rot and decay and lot more problems than you bargained for. Mold ad fungus can take root and find their way into the house. It is important to make proper inspection of the roofs after rainstorms and windy days. If you see any shingles or metal pieces from your roof on the ground then you know some damage has happened and needs to be looked into. Do this only after the water has completely dried up and there is no danger of you slipping and falling during the inspection.

Replacing roof shingles can be done in two ways. Either you can rip up the old shingles completely, dispose them off and replace with brand new shingles – either 30-year or 40-year shingles depending on your budget or go for second layer of shingles over the old layer. The first option is more expensive as the removal and disposal of old shingles cost money which your contractor will add to your roofing cost. In the second method the roof is prepared, old worn-out, warped, curled and misshapen shingles are removed and surface is made as even as possible. Only, then is the second layer of shingles is installed. This saves money as you don’t have to pay for removing and hauling away of the old debris.

The first methods gives better results and the second method is gaining popularity too. But, if the surface is not prepared according to the guidelines then there is the danger of the shingles failing before their promised life-span.

CONTINUE READING

Replace Roof Shingles – Maintenance Is Key To Long-Life Of Roofing Shingles

Every responsible homeowner will replace roof shingles that are damaged as soon as they notice them rather than neglect it and end up replacing them entirely which is a nightmare that is best avoided. A careful maintenance schedule that makes sure the roof is in top condition should be right at the top of list of things to do on a homeowners maintenance schedule. Annual or twice yearly inspections and maintenance is a must.

Apart, from this whenever there are strong winds, heavy rains, storms, blizzards or hurricanes you will have to make sure your roof has not been damaged in any way. If you find any signs of damage then fixing it immediately avoids water seeping through the exposed areas and finding their way into the house. Water damage can be very expensive for your home. The water rot the wood sheeting and ruin the paint job in the interiors if neglected for long. Replace roof shingles that are damaged and fix any potential problems and you can sleep at night peacefully. Neglecting this simple tasks can literally hundreds or even thousands of dollars to your roofing bill.

It is time to replace roof shingles if your roof is 20 years or older. If you find roof shingles that are badly damaged, worn, curled, cracked or broken then replace them. Assess the damage to see if it needs partial repairs or a complete overhaul of the whole roof. If it’s simple matter of replacing a few worn out shingles or nailing back shingles that have come loose in wind or lifted up due to improper nailing then you can do it yourself.

If your roof is a shallow or medium pitch roof on which you can walk comfortably without the danger of you slipping and falling, then replace roof shingles that you think are potential problem makers. There are 3 most common problems usually a homeowner will face during this inspections and which are easily fixed without involving a roofing contractor. Make sure it is warm and dry afternoon when the shingles are supple and easy to install. Don’t do this in the early mornings when there is dew or when the roof is wet and slippery.

Missing Shingles

If you find any shingle or part of shingle missing then replace the whole shingle. If you have left-over shingles from your last job then the use them else you can buy a bundle from the roofing supplies store. Get a close match if you can’t find the same shingle type as your roof. Tools you will need include hammer, pry bar, knife to cut the shingles to required size, roofing nails. Every shingles needs 4 nails. When the course above is installed the nails from that course also pass through the top edge of these shingles.

Use the pry bar to remove the first row of nails by sliding the pry bar under the shingle that is above the damaged shingle. Gently lift and free from the sealer strip. You will see the nails keeping the damaged shingle in place. Pry upwards, once the nail comes up about quarter inch press the shingle down and remove the nail. Do this with remaining 3 nails. Now, put the bar under the shingle directly above damaged one and remove second row of nails. Once all 8 nails are out, you can pull out the damaged shingle. Now, replace roof shingles in place of old, damaged ones.

Sometimes, you can’t removed nails as the shingle is brittle and cracked. Cut v-notches on the replacement shingle to fit under the nails and nail it place at 4 other places.

Curled Shingles

Due to age or constant exposure to elements the shingles curl at the corners. If you notice it, then glue it down. A caulking gun sprays a little glue under the shingle and press it down. Weigh it down for 24 hours. There is no need to replace roof shingles here.

Cracked Shingles

A cracked and torn shingle doesn’t mean you have to replace roof shingles. Apply a thick bead of roofing sealant under both sides of cracked shingles. Press the shingle down. Now, apply another bead of sealant on top and spread it around with your putty knife. Just sprinkle some colored granules found in the gutter and no one will know that you have fixed it.

CONTINUE READING

How To Replace Roof Shingles – Safety And Effective Roofing Guidelines

How to replace roof shingles is often asked question among homeowners facing minor or major roof damage. A rainstorm or hurricane might have dislodged a few shingles or a couple of shingles might have cracked due to falling debris or the whole roof might need replacement because of age. For the minor repairs it would be absolute waste of time and money to employ a roofer when the homeowner is competent enough to do the job himself/herself.

This informative guide will help you through the process of replacing roof shingles and not waste your money on expensive roofing contractors. So, before we start you should remember that the first and foremost step every “how to replace roof shingles” guide emphasizes is about safety. Roofing has to be done at several feet above the ground and a person not accustomed to working at heights and has a phobia for them should avoid it. It is to some extent dangerous work so, all precautions need to be taken to make yourself as secure as possible when working up there.

Make your ladder secure, if it falls down or blown away, you will have jump a long distance and that can land you straight away in the hospital. Have an assistant to help you out to hold the ladder or to hand you the tools. Having another person around is always comforting and in case of an emergency they can seek help. Steeper slopes are more difficult to walk on and so you should hire roof jacks and walk boards. Learn how to them up securely and safely. If in doubt hire a professional. A few hundred dollars saved in roofer’s fees is not worth you seriously hurting yourself.

Power lines are another danger. They carry high amounts of current and if you contact with these high tension wires you can be electrocuted. So, make sure you as far away from them as possible. If you have to move it out your way, then use a long dry wooden pole with Y-shaped ending that can keep the wire away as you work. This is again a very dangerous situation and if your home is in the vicinity of power cables then be very careful or hire a professional who know how to handle it.

Keep those two points firmly in mind before learning how to replace roof shingles. The first step is to place ice and water shield. This will prevent ice backing up. Place these shields in the valleys also. Next, place felt on the decking. Use 30 pound or 15 pound felt though the former is preferable. Nail it in place. Three rows of nails are generally needed but in high wind areas 4 rows may be needed. Install drip edges starting at the eaves.

Next, comes shingles installation in how to replace roof shingles step-by-step guide. Begin with the starter course of 3 tab shingles with the tabs removed. The shingles need to overhang over the drip edge by at least half an inch. In the next row, cut off about 6 inches of the first shingle and install it. This is to prevent the lining up of the shingles. Nail the shingles 4 per shingle. Nail high and don’t let the nail go through the shingle. Stagger the shingles.

Read the instructions on the shingles pack about how to replace roof shingles and follow them including the nailing pattern. Start from the bottom and work your way upwards till the ridge. At the valleys and vents in the roof you will need flashing. After the flashing is installed, shingles have to be installed over it. At each stage ensure that there is lot of overlap to avoid any leaks or water seepage. Apply the cap at the ridges.

The above is not an exhaustive guide on how to replace roof shingles.

CONTINUE READING